Changing the blade on a cordless tool is an easy way to update the look of your Jigsaw. There are two ways to change the blade on your Jigsaw. One is by removing the housing and replacing it with a new one, and the other is removing the housing and changing the blade yourself.
Removing the Housing
This method requires you to have a sharp knife, Stanley wrench, fine-pointed screwdriver, or similar tool. You will need some sort of support to hold your tool while you remove it.
You can also buy new blades at Black and Decker’s website. They offer different lengths of blades so you can have longer lasting tools that last longer!
Removing a blade requires being careful not to cut yourself as some materials may be hard or soft against exposed skin.
Contents:
Remove the cover
Now that your battery is fully charged, it is time to remove the cover. This can be a little tricky at first, but keep reading and try again next week!
To remove the cover, you must first pull out the blade. You will do this by pulling on the end of the tool and releasing. Then you must slide off the blade.
Once both sides are off, you can shake or tap them apart to let out any charge. To re-insert the tool, pull out firmly and slide back in. Done!
You will want to do this a few times while the tool is on to get a full charge out of it.
Loosen the screw holding the blade
Next, remove the bottom of the jigsaw. You can do this by lifting up one of the sides, or by simply removing the screw that holds it in.
With the blade removed, you can now easily change its blade. To do this, slide the new blade into place until it clicks into place. Now push down on the new blade and pull out the old one to install it.
Now repeat all of these steps with the new blade to set it up properly and put away your jigsaw.
How to Change Blade on Black and Decker Jigsaw Tips and Tricks
Try some of these tips out before you leave for your next woodworking project. They may help you work quickly and efficiently on your next woodworking project!
Do not remove any of the dust cover from your Black & Decker Jigsaw when changing blades. This could make it difficult to reinstall a new blade when needed.
Remove the blade from the holder
Now, you want to remove the blade from the holder. This is done by pulling gently on the retainer ring at the top of the motor.
This allows space for the blade to come out. If you had to put it in while it was charging, now is the time!
Once removed, you can replace the blade or keep using your old one. Both take about a minute to set up and charge!
NOTE: If you have a flush finish black and decker jigsaw, do not worry about putting a new blade on before removing the old one.
Install new blade
Before installing the new blade, you should remove the old one. You can do this by either using a sharp knife or dulling tool or by pulling the handle out.
To remove the blade, you can do two things. You can either cut along the edge of the blade to release it from the Jigsaw, or you can pull on the handle to disengage it from the Jigsaw.
Either way, you will have to re-install the blade from the outside in!
Important: When placing a new blade on your Jigsaw, make sure it is level and that there are no sharp edges on it. If there are any exposed blades, place them covered with a piece of cardboard or another item to prevent cutting yourself.
Tighten the screw holding the blade
When changing the blade on your Black and Decker jigsaw, you will need to tighten the screw holding the blade in place. This can be done by pulling up on the handle with your hand until the blade is secured.
Once this is done, you can move on to cutting!
How to Change Blade on Black and Decker Jigsaw How to Change Blade on Black and Decker Jigsaw – This article will explain how to change the blade on your Black and Decker jigsaw. This article will explain how to change the blade on your Black and Decker jigsaw. – A free tool can be used to assist in changing the blade on your jig- Eye glasses or a magnifying device may be needed for this process. – First, remove the backing by pulling off one of the tabs found at either end of the tool. – Next, removethe screw that holds in placethe blade by gently turning it until it comes loose.
Put back the cover
After taking the blade out, you will put it back in the Jigsaw. This is to protect the hard workpiece from getting damaged while you sharpen your Jigsaw’s blade.
To put it back, first apply some lubricant to the pivot point and slide the tool back onto it. Then, tighten the screw down to lock it in place.
This process takes a minute or so, so don’t get too frustrated! You want to do this just before you start doing other projects so that you have extra lubricant for your Jigsaw.
You can also use a hair dryer or household vacuum cleaner to remove any dust from your Jigsaw during this process.
Trigger test
If your Black and Decker Jigsaw does not hold a charge, it is time to test the trigger. When the tool is not power-son, it can be difficult to tell if the battery is full or not.
To perform a trigger test, start the tool with the disk removed and then reinserting. During this process, keep the disk in place to see if it turns as it locks into place. If it does, you have successfully charged the battery!
If the blade turns when you insert and remove the disk, then your battery is fully charged and ready to go! If nothing happens when you try to turn the tool on and off, then there may be an issue with your charger connection.
Blade test
When changing the blade on a Jigsaw, there’s a rule to follow. You want to test the depth of the new blade against the old one to make sure it fits properly.
This means you must take apart your Jigsaw and remove the old blade before you can put the new one in. You can test fit the new blade into both slots and see if it fits. If not, contact Black & Decker customer service to find out why not.
Once it is in, try your glue job with something smooth and firm like a piece of cardboard. If it holds, then that was success! If not, contact customer service again. It is important that these calls are done by phone because if you have no way to change the blade, then someone will send you back an old model that does not work.