Simplisafe is a doorbell and home security system that features a camera, transmitter, and receiver. It allows you to monitor your home from a smartphone app or with a limited-use desktop software. You can also see your home from the app or via the security camera monitoring platform.
This system requires you to install two devices in your home: the transmitter and the receiver. The transmitter monitors the entry points into your home and detects anybody attempting to gain access via the doorbell connection. The receiver connects to it and determines when somebody rings the bell, allowing you to lock or release based on who it is.
This article will talk about how to remove Simplisafe Doorbell From Wall using an image file downloader program such as WinZip or 7-Zip. You can also use simplicityexplorer if you do not have those programs available.
Contents:
Pull off exterior doorbell cover
Now that you have the Simplisafe doorbell ready to go, it is time to remove it from the wall. First, you will need to pull off the exterior cover. This can be done by removing two screws from the wall behind the doorbell and pulling up on the cover.
Once removed, you can now handle all of your wires and covers as if nothing was there. You will need to run a power line down to connect your smart phone or other device, however.
Now that you have removed all of the protection against unauthorized users, you can handle having someone view your home as they normally would. You do not need a security system for this method!
Reminder: Make sure to remove the doorbell and bell cover properly in case of water or fire damage.
Remove battery terminal tabs
When your Simplisafe doorbell is connected, you can detach the battery terminal tabs by pressing and holding the button for 3 seconds. This will open a door on your Simplisafe app. You can then pull the door away and test the connection by pressing and holding the button for 3 seconds to connect then release to remove.
To re-attach, press and hold the button for 3 seconds to close the door. You will have to repeat this process a second time to get it back up.
This step can be done before or after installing new batteries as it does not change anything while they are in. You can also do this while the house is occupied as there is no risk of someone getting out of reach!
This method works with both video and sound calls so you do not need to limit yourself to just your voice.
Use flathead screwdriver to remove screws from bell chamber
After you install the doorbell, it is time to connect it to the wall. You can use a bit of tape or glue to secure the bell to the frame.
To remove the device from the wall, you must first remove two screws that hold it in. You can do this by using a flathead screwdriver and just pulling on the device until it comes loose.
You can then replace it or buy a new one!
Using a bit of glue and a small piece of tape, secure the bottom of the device to the wall. This will prevent it from moving while you work on fixing it.
After that, you can remove the two screws holding in the bell chamber.
Remove wire connections from chime unit
If you have a Simplisafe chime unit, you can remove the wire connections by cutting the wire at the connector.
To do this, locate the connector at the bottom of the unit and cut along the wire connections at that location. You will need to cut all of them to remove the chime unit!
This step will prevent future problems with connecting and disconnecting the unit.
Remove electronic components from doorbell
If you have an electronic component in your doorbell such as a camera or audio system, take it out before cutting wires. Doing so may help solve problems with jamming or popping if someone tries to open your door.
Cut power cables from wall switch (if applicable) and place them outside to stop them getting stuck or entangled in walls.
Pull off chime unit cover
If you want to access the Simplisafe doorbell from the outside, then you’ll need to remove the cover on the chime unit.
To do this, pull off the clear cover and reveal the button inside. You can then disconnect or remove the power source from the unit.
Remove mounting bracket from wall
If you’re looking to remove the mounting bracket for the Simplisafe doorbell from your wall, do it before installing the new unit. The new unit requires a different location for its mounting bracket compared to the old one.
To remove the old bracket, you must first trim off some of the insulation tape that is holding it in place. Then, you can easily remove the arm and install your new unit.
To install the new unit, you must first expose some of the wiring behind where the doorbell should go and then connect it to an electrical outlet.
Take pictures of installation for reference
If you have a Simplisafe doorbell, take pictures of the following:
When installing a doorbell, there are two major components: The receiver and the wires. To remove the receiver and wires, you will need to take them off.
To do this, you will first need to take pictures of the installation process. Then, you can use any of the following methods: Use an electric knife or cable cutters to cut the receiver and wires away. Use a paper hole punch or cable tie pullers to put pressure on the wall behind the door.
Check warranty status of system
If your Simplisafe doorbell has failed or been tampered with, check the warranty status of the system.
Most companies offer a one-year warranty on their products. If your system has a more long-lasting warranty, it may be worth calling the manufacturer to see if you can upgrade to a new unit.
To do so, you’ll need to replace your current unit, which may be difficult or even illegal to change yourself. It may also be possible to have the company do it for you, but then you’re paying for a service that was not needed originally.
Look for seals and other indicators that indicate the system has failed. If there is evidence of tampering, you may be able to retrieve data from the units by manually depressing buttons or keys on them.